[Orca-users] running make after configure

[tburke at timebridge.com]

In my instance I'm was nfs mounting perl in /usr/local.  I dont have
permission to put the modules there so I went and got perl 5.6.1.  I
extracted orca to /opt/orca-0.26.  I've created a mount point /orca
for the files.  I also placed perl in /orca as below

/orca/var/orca/orcallator
/orca/var/orca/rrd/orcallator
/orca/var/orca/rrd
/orca/var/orca
/orca/var
/orca/lib/Orca
/orca/lib/perl5/5.6.1
/orca/man/man1

etc.

I run configure as below...
configure --prefix=/orca --with-html-dir=/orca/html

configure runs fine but make give the following error

# make
cd packages && make CFLAGS=-g -O2
make[1]: Entering directory `/opt/orca-0.26/packages'
cd Digest-MD5-2.09 && /orca/bin/perl Makefile.PL
Testing alignment requirements for U32... u32align.c:9: EXTERN.h: No
such file or directory
u32align.c:10: perl.h: No such file or directory
Can't compile test program
Checking if your kit is complete...
Looks good

Error: Unable to locate installed Perl libraries or Perl source code.

It is recommended that you install perl in a standard location before
building extensions. Some precompiled versions of perl do not contain
these header files, so you cannot build extensions. In such a case,
please build and install your perl from a fresh perl distribution. It
usually solves this kind of problem.

(You get this message, because MakeMaker could not find
"/usr/local/lib/perl5/5.6.1/sun4-solaris/CORE/perl.h")
make[1]: *** [Digest-MD5-2.09/Makefile] Error 2
make[1]: Leaving directory `/opt/orca-0.26/packages'
cd lib && make CFLAGS=-g -O2
make[1]: Entering directory `/opt/orca-0.26/lib'
make[1]: Nothing to be done for `all'.
make[1]: Leaving directory `/opt/orca-0.26/lib'
cd src && make CFLAGS=-g -O2
make[1]: Entering directory `/opt/orca-0.26/src'
make[1]: Nothing to be done for `all'.
make[1]: Leaving directory `/opt/orca-0.26/src'
cd orcallator && make CFLAGS=-g -O2
make[1]: Entering directory `/opt/orca-0.26/orcallator'
cat ../config/PerlHead1 orcallator_running.pl > orcallator_running
chmod 0755 orcallator_running
cp restart_orcallator.sh restart_orcallator
chmod 0755 restart_orcallator
cp stop_orcallator.sh stop_orcallator
chmod 0755 stop_orcallator
cp start_orcallator.sh start_orcallator
chmod 0755 start_orcallator
cp S99orcallator.sh S99orcallator
chmod 0755 S99orcallator
make[1]: Leaving directory `/opt/orca-0.26/orcallator'
cd docs && make CFLAGS=-g -O2
make[1]: Entering directory `/opt/orca-0.26/docs'
pod2man ../src/orca.pl > orca.man
syntax error at /orca/lib/perl5/5.6.1/warnings.pm line 311, near "{^"
BEGIN failed--compilation aborted at /orca/lib/perl5/5.6.1/vars.pm
line 12.
BEGIN failed--compilation aborted at
/orca/lib/perl5/5.6.1/Getopt/Long.pm line 37.
BEGIN failed--compilation aborted at /orca/bin/pod2man line 15.
make[1]: *** [orca.man] Error 2
make[1]: Leaving directory `/opt/orca-0.26/docs'
make: *** [all] Error 2


I searched the posts and found some similar items.  I'm sure I'm just
missing something simple in the setup.  Any ideas?

Mike