[Orca-users] Re: gigswift support

[Blair Zajac]

I would then upgrade to the latest orcallator.se file.  I believe
that orcallator_column needs the exact column name, so try a

    grep ce0 orcallator-200.......

and see if it's there.

Best,
Blair

orcausers wrote:
> 
> except i don't see any data columns in the orcallator file that would
> indicate this data is being recorded at all - i believe i would be
> looking for a ce0 column using the orcallator_column utility.
> here is an edited  netstat -i
> # netstat -i
> Name  Mtu  Net/Dest      Address        Ipkts  Ierrs Opkts  Oerrs
> Collis Queue
> lo0   8232 loopback      localhost      481925989 0     481925989
> 0     0      0
> ce0                                    2456263904 0     1186215456
> 0     0      0
> qfe2                                      1979604 0     98     0
> 0      0
> qfe3                                        0      0     0      0
> 0      0
> so there is activity -
> i am trying to get ce0 on the graphs -
> 
> the qfe2 graph shows data - the qfe3 (althought all 0's appears) but
> my goal is to get the ce0 interface on the graphs - it is a cPCI
> gigswift card (compact gigaswift card).
> 
> i must be missing something (either a concept or a config item).
> thanks for the help.
> mik
> 
> --- In orca-users at y..., Blair Zajac <blair at o...> wrote:
> > orcausers wrote:
> > >
> > > sorry - i meant the newest orcallator.se file - 1.35 - .
> >
> > No, you shouldn't need that.  Just the latest orcallator.cfg file.
> >
> > Best,
> > Blair
> >
> > >
> > > --- In orca-users at y..., Blair Zajac <blair at o...> wrote:
> > > > orcausers wrote:
> > > > >
> > > > > curently running orca o.26beta1 - sorry dont know .cfg level -
> > > > > and setoolkit 3.2 with 1.25 se file.
> > > > >
> > > > > i need to upgrade to cfg 1.35 to get gig support - do i have
> to
> > > > > upgrade to se 1.35 at the same time?
> > > >
> > > > There is no SE 1.35.  You mean orcallator?  No, older versions
> > > should
> > > > pick up the card.  However, check the output data files from
> your
> > > > orcallator.se just to make sure the data is being measured.  If
> not,
> > > > then I would upgrade.
> > > >
> > > > >
> > > > > do i have to upgrade to setoolkit 3.3 also?
> > > > > and  to orca 0.264 ?
> > > >
> > > > No.  You should not need to.
> > > >
> > > > >
> > > > > and do i have to do all the domains at once if i upgrade orca
> to
> > > cfg
> > > > > 1.35 to get the gig support - i don't have these gig cards on
> all
> > > the
> > > > > domains but i think in previous conversation - it was all had
> to
> > > go
> > > > > at once.
> > > >
> > > > No, you just need to upgrade the orcallator.cfg file on the
> system
> > > that
> > > > runs Orca (you should only have one system running Orca).
> > > >
> > > > Best,
> > > > Blair